Troubleshoot a guitar
Find what you're hearing, then do the meter test before you desolder anything. A cheap meter on the ohms setting finds most wiring faults in a few minutes.
- No sound at allSilent in every position, every knob up.
- Hum gets louder when you touch the stringsTouching the strings or bridge makes it worse, not better.
- Buzz that doesn't change when you touch the stringsA steady buzz, and your hand on the bridge does nothing.
- Buzz from one part of the guitar, or a pot that hums when touchedA part buzzes, or touching one knob changes the noise.
- Cuts in and outDrops out when you move, or when the cable moves.
- One pickup is deadThe others work, but one position or pickup is silent.
- Thin, quiet sound when two pickups are onEach pickup alone sounds right, but together they sound hollow and weak.
- Volume works backwards, or cuts off too earlyLoud at 0, quiet at 10, or most of the sweep does nothing.
- Tone knob does nothingTurning the tone down doesn't darken the sound.
- Crackle or scratching when you turn a knobNoise only while the knob moves.
No sound at all
Silent in every position, every knob up.
What it usually is
- The cable or the amp, more often than you'd think. Try another cable and another guitar first.
- The hot wire to the jack tip has come off, or a stray strand is touching ground.
- The volume pot's middle lug isn't connected to the jack.
Where to look
Look at the jack first. The tip lug is the short one that touches the tip of the plug; the sleeve lug is the long one that touches the barrel.
Look for a blob of solder bridging two lugs on the volume pot.
Meter test. Ohms, 20k range, knobs on 10. Plug a cable in and touch the meter to the cable's tip and sleeve. A few thousand ohms means the pickups reach the jack and the fault is past it. Near 0 means hot touches ground somewhere. No reading at all means the hot path is open.
Hum gets louder when you touch the strings
Touching the strings or bridge makes it worse, not better.
What it usually is
- The jack is wired backwards: the hot wire is on the sleeve lug and the grounds are on the tip lug.
Where to look
Follow the bare ground wires. They should all end on the jack's long sleeve lug, never the short tip lug.
Meter test. Ohms. Touch one probe to the strings and the other to the cable's sleeve. It should read close to 0. If 0 shows on the cable's tip instead, the jack is backwards: swap the two wires on the jack.
You can spot this one on a drawing in Practice.
Buzz that doesn't change when you touch the strings
A steady buzz, and your hand on the bridge does nothing.
What it usually is
- The bridge or tailpiece ground wire is missing or broken, so the strings aren't grounded.
- On a Strat, the wire to the trem claw has come off the claw or the pot back.
Where to look
Find the wire that runs from the control cavity to the bridge, tailpiece stud or trem claw, and check both ends.
Meter test. Ohms. Strings to the cable's sleeve should read under 1 ohm. If you get no reading, the bridge ground is broken somewhere along that wire.
You can spot this one on a drawing in Practice.
Buzz from one part of the guitar, or a pot that hums when touched
A part buzzes, or touching one knob changes the noise.
What it usually is
- A pot back isn't grounded. Every pot case should be tied to the rest of the ground with a wire or a shared ground plate.
- Shielding paint or foil that doesn't touch ground.
Where to look
Check that each pot back has a ground wire soldered to it, and that the solder actually took (it should look shiny and flowed, not balled up).
Meter test. Ohms. From each pot back to the cable's sleeve should read under 1 ohm. Any pot back that reads open is floating.
You can spot this one on a drawing in Practice.
Cuts in and out
Drops out when you move, or when the cable moves.
What it usually is
- A loose jack. The nut works loose, the jack turns, and the wires twist off the lugs.
- The jack's tip spring has lost tension and doesn't grip the plug.
- A cold solder joint that looks fine but isn't bonded.
Where to look
Tighten the jack nut while you hold the jack still from inside, so it doesn't spin.
Gently bend the tip spring in so it grips the plug firmly.
Meter test. Ohms, cable plugged in, probes on the cable's tip and sleeve. Wiggle the cable and tap each joint with a chopstick. A steady reading that jumps or drops out points you to the bad joint.
One pickup is dead
The others work, but one position or pickup is silent.
What it usually is
- A pickup lead has come off its switch lug.
- The pickup's coil is broken. It happens, mostly to old or abused pickups.
Where to look
Check that pickup's leads at the switch. On a humbucker, also check the two leads that are joined and taped up; they have to stay joined to each other.
Meter test. Ohms, across that pickup's own hot and ground leads. Most single coils read roughly 5k to 8k ohms and most humbuckers roughly 7k to 17k. A pickup that reads in range is fine and the fault is in the wiring. No reading means the coil or a lead is broken.
Thin, quiet sound when two pickups are on
Each pickup alone sounds right, but together they sound hollow and weak.
What it usually is
- The two pickups are out of phase. One of them has its hot and ground leads the other way round.
Where to look
Swap the hot and ground leads of one pickup. On a 4-wire humbucker, swap only the hot and the ground lead; leave the two joined leads joined, and the bare wire to ground.
Meter test. Your meter readings will look normal, because a meter can't see phase. Swap one pickup's leads and listen. If the hollow sound turns full, you found it.
Volume works backwards, or cuts off too early
Loud at 0, quiet at 10, or most of the sweep does nothing.
What it usually is
- The outer lugs of the volume pot are swapped. The pickup goes to lug 3 and ground goes to lug 1.
- A linear pot where an audio taper pot belongs makes the volume feel like it all happens near the top.
Where to look
Look at the back of the pot with the lugs pointing up: lug 1 is on the left, and ground goes there.
Meter test. Ohms, probes on the cable's tip and sleeve. With the volume on 10 you should see the full pickup reading, and it should fall to almost 0 as you turn it down. If it rises as you turn down, the outer lugs are swapped.
Tone knob does nothing
Turning the tone down doesn't darken the sound.
What it usually is
- One leg of the tone cap isn't soldered, or the cap goes to the wrong lug.
- The tone pot isn't connected to the pickup it's supposed to control.
Where to look
Check both legs of the cap. One goes to the tone pot's lug, the other goes to ground, usually the pot back.
Meter test. A cap blocks the meter's current, so the cap itself reads open, and that's normal. Check the wires around it instead: from the cap's ground leg to the cable's sleeve should read close to 0.
Crackle or scratching when you turn a knob
Noise only while the knob moves.
What it usually is
- Dirt or wear inside the pot.
Where to look
Spray a little contact cleaner into the opening on the pot's side and turn it end to end a dozen times. If the crackle comes back, replace the pot.
Meter test. Ohms across the cable's tip and sleeve while you sweep the knob slowly. The reading should change smoothly. Jumps and flickers mean the pot is worn.