Wiring Bench

Neck and bridge tones

Wiring diagram: Strat style, SSS, 5-way blade

Build code S3-FFF-5W-V2B-A-22-M-001-NNN

Switching

Switching chart: 1 bridge, 2 bridge + middle, 3 middle, 4 middle + neck, 5 neck

Parts

QtyPart
1Neck pickup: single coil
1Middle pickup: single coilRWRP: reverse wound, reverse polarity
1Bridge pickup: single coil
15-way blade
3250k audio (A) potvolume, tone neck mid, bridge tone
122 nF (.022 µF, marked 223) capacitortone
1Mono output jack
1Bridge ground wireto the trem claw
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

Tone 1 works on the neck and middle, tone 2 on the bridge. The usual layout on newer Strats. Single coil in the neck, single coil in the middle, single coil in the bridge. 5-way blade. 1 volume, 2 tones (bridge tone, 250k pots, 22 nF cap, modern tone wiring). The middle pickup is reverse wound, reverse polarity. Bridge ground to the trem claw.

VolumeTurns the whole guitar up and down.
Tone neck midRolls off treble on the neck and middle pickups. Down makes it warmer and darker.
Bridge toneRolls off treble on the bridge pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the 5-way blade, Volume, Tone neck mid, Bridge tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Tone neck mid pot back to Volume pot back.
  2. Bare wire from Bridge tone pot back to Tone neck mid pot back.
  3. Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
  4. Wire from Output jack sleeve to Volume pot back.
  5. Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from 5-way blade AC to 5-way blade BC.
  2. Wire from 5-way blade B2 to 5-way blade B3.

Caps and resistors

  1. 22 nF cap: one leg on Tone neck mid lug 1, the other on Tone neck mid pot back. Caps have no right way round.

Switch and pot runs

  1. Wire from 5-way blade BC to Volume lug 3.
  2. Wire from 5-way blade B3 to Tone neck mid lug 2.
  3. Wire from 5-way blade B1 to Bridge tone lug 2.
  4. Wire from Bridge tone lug 1 to Tone neck mid lug 1.

To the output jack

  1. Wire from Output jack tip to Volume lug 2.

Pickups last

  1. Neck single coil black lead to Volume pot back.
  2. Neck single coil white lead to 5-way blade A3.
  3. Middle single coil black lead to Volume pot back.
  4. Middle single coil white lead to 5-way blade A2.
  5. Bridge single coil black lead to Volume pot back.
  6. Bridge single coil white lead to 5-way blade A1.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
5-way blade 1 (bridge)bridgeabout 5.9k ohms
5-way blade 2 (bridge + middle)bridge parallel with middleabout 3.0k ohms
5-way blade 3 (middle)middleabout 5.9k ohms
5-way blade 4 (middle + neck)middle parallel with neckabout 3.0k ohms
5-way blade 5 (neck)neckabout 5.9k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this