Strat 7-sound
Build code S3-FFF-5W-V2T-A-22-M-001-NNN-JN
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: single coil | |
| 1 | Middle pickup: single coil | RWRP: reverse wound, reverse polarity |
| 1 | Bridge pickup: single coil | |
| 1 | 5-way blade | |
| 2 | 250k audio (A) pot | volume, middle tone |
| 1 | 250k audio (A) push-pull pot (DPDT) | neck tone |
| 1 | 22 nF (.022 µF, marked 223) capacitor | tone |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the trem claw |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
Pull a knob to add the neck in any position: bridge plus neck, and all three. Single coil in the neck, single coil in the middle, single coil in the bridge. 5-way blade. 1 volume, 2 tones (250k pots, 22 nF cap, modern tone wiring). The middle pickup is reverse wound, reverse polarity. Pull the neck tone knob: adds the neck. Bridge ground to the trem claw.
| Volume | Turns the whole guitar up and down. |
| Neck tone | Rolls off treble on the neck pickup. Down makes it warmer and darker. |
| Middle tone | Rolls off treble on the middle pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 5-way blade, Volume, Neck tone, Middle tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Neck tone pot back to Volume pot back.
- Bare wire from Middle tone pot back to Neck tone pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 5-way blade AC to 5-way blade BC.
Caps and resistors
- 22 nF cap: one leg on Neck tone lug 1, the other on Neck tone pot back. Caps have no right way round.
Switch and pot runs
- Wire from 5-way blade A3 to Neck tone AC.
- Wire from 5-way blade BC to Volume lug 3.
- Wire from Neck tone A up to Volume lug 3.
- Wire from 5-way blade B3 to Neck tone lug 2.
- Wire from 5-way blade B2 to Middle tone lug 2.
- Wire from Middle tone lug 1 to Neck tone lug 1.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck single coil black lead to Volume pot back.
- Neck single coil white lead to 5-way blade A3.
- Middle single coil black lead to Volume pot back.
- Middle single coil white lead to 5-way blade A2.
- Bridge single coil black lead to Volume pot back.
- Bridge single coil white lead to 5-way blade A1.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 5-way blade 1 (bridge), Neck tone down (pushed: switch as usual) | bridge | about 5.9k ohms |
| 5-way blade 1 (bridge), Neck tone up (pulled: adds the neck) | bridge parallel with neck | about 3.0k ohms |
| 5-way blade 2 (bridge + middle), Neck tone down (pushed: switch as usual) | bridge parallel with middle | about 3.0k ohms |
| 5-way blade 2 (bridge + middle), Neck tone up (pulled: adds the neck) | bridge parallel with middle parallel with neck | about 2.0k ohms |
| 5-way blade 3 (middle), Neck tone down (pushed: switch as usual) | middle | about 5.9k ohms |
| 5-way blade 3 (middle), Neck tone up (pulled: adds the neck) | middle parallel with neck | about 3.0k ohms |
| 5-way blade 4 (middle + neck), Neck tone down (pushed: switch as usual) | middle parallel with neck | about 3.0k ohms |
| 5-way blade 4 (middle + neck), Neck tone up (pulled: adds the neck) | middle parallel with neck | about 3.0k ohms |
| 5-way blade 5 (neck), Neck tone down (pushed: switch as usual) | neck | about 5.9k ohms |
| 5-way blade 5 (neck), Neck tone up (pulled: adds the neck) | neck | about 5.9k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
Stock Strat style
Five sounds on a 5-way blade, with quiet mixes in 2 and 4.
Neck and bridge tones
Tone 1 works on the neck and middle, tone 2 on the bridge. The usual layout on newer Strats.
7-sound on a toggle
A separate on/off switch adds the neck, for bridge plus neck and all three.
No-load neck tone
The neck tone knob drops out at 10 for a little more sparkle.