Wiring Bench

One humbucker, 3-way mini

Wiring diagram: One pickup, H, No switch

Build code J1-H-NO-V1T-A-22-M-001-T

Switching

Switching chart: 1 bridge full humbucker, 2 bridge one coil, 3 bridge parallel

Parts

QtyPart
1Bridge pickup: humbucker
1Bridge humbucker mini toggle
2500k audio (A) potvolume, tone
122 nF (.022 µF, marked 223) capacitortone
1Mono output jack
1Bridge ground wireto the bridge stud
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

An on-on-on mini toggle: full humbucker, one coil, or both coils in parallel. Humbucker in the bridge. 1 volume, 1 tone (500k pots, 22 nF cap, modern tone wiring). An on-on-on mini toggle sets the bridge humbucker: up for the full humbucker, middle for one coil, down for both coils in parallel. Bridge ground to the bridge stud. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.

VolumeTurns the whole guitar up and down.
ToneRolls off treble on every pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the Bridge humbucker mini toggle, Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Tone pot back to Volume pot back.
  2. Wire from Bridge humbucker mini toggle A down to Volume pot back.
  3. Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
  4. Wire from Output jack sleeve to Volume pot back.
  5. Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from Bridge humbucker mini toggle A up to Bridge humbucker mini toggle B up.

Caps and resistors

  1. 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.

Switch and pot runs

  1. Wire from Bridge humbucker mini toggle B down to Volume lug 3.
  2. Wire from Tone lug 2 to Volume lug 3.

To the output jack

  1. Wire from Output jack tip to Volume lug 2.

Pickups last

  1. Bridge humbucker green and bare leads to Tone pot back.
  2. Bridge humbucker white lead to Bridge humbucker mini toggle AC.
  3. Bridge humbucker red lead to Bridge humbucker mini toggle BC.
  4. Bridge humbucker black lead to Bridge humbucker mini toggle B down.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
Bridge humbucker mini toggle 1 (bridge full humbucker)bridgeabout 7.9k ohms
Bridge humbucker mini toggle 2 (bridge one coil)bridge south coilabout 4.0k ohms
Bridge humbucker mini toggle 3 (bridge parallel)bridge (coils in parallel)about 2.0k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this

One humbucker, 3-way mini wiring diagram | Wiring Bench