Wiring Bench

Series/parallel toggle

Wiring diagram: Humbucker series/parallel toggle

Hand-wired example, so it has no build code.

Switching

Switching chart: 1 series, 2 parallel

Parts

QtyPart
1Hb pickup: humbucker
1Mini toggle (on-on)
2500k audio (A) potvolume, tone
122 nF (.022 µF, marked 223) capacitortone
1Mono output jack
1Bridge ground wire
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

A small toggle sets one humbucker to full and thick, or bright and still quiet.

VolumeTurns the whole guitar up and down.
ToneRolls off treble on every pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the Mini toggle (on-on), Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Tone pot back to Volume pot back.
  2. Wire from Mini toggle (on-on) A 2 to Volume pot back.
  3. Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
  4. Wire from Output jack sleeve to Volume pot back.
  5. Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from Mini toggle (on-on) A 1 to Mini toggle (on-on) B 1.

Caps and resistors

  1. 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.

Switch and pot runs

  1. Wire from Mini toggle (on-on) B 2 to Volume lug 3.
  2. Wire from Tone lug 2 to Volume lug 3.

To the output jack

  1. Wire from Output jack tip to Volume lug 2.

Pickups last

  1. Hb humbucker green and bare leads to Tone pot back.
  2. Hb humbucker black lead to Volume lug 3.
  3. Hb humbucker white lead to Mini toggle (on-on) AC.
  4. Hb humbucker red lead to Mini toggle (on-on) BC.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
Mini toggle (on-on) 1 (series)hbabout 7.9k ohms
Mini toggle (on-on) 2 (parallel)hb (coils in parallel)about 2.0k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this