Wiring Bench

4-way with series

Wiring diagram: Tele style, SS, 4-way blade

Build code T2-FF-4W-V1T-A-47-M-001-NN

Switching

Switching chart: 1 bridge, 2 both parallel, 3 neck, 4 both series

Parts

QtyPart
1Neck pickup: Tele pickupRWRP: reverse wound, reverse polarity
1Bridge pickup: Tele pickup
14-way blade
2250k audio (A) potvolume, tone
147 nF (.047 µF, marked 473) capacitortone
1Mono output jack
1Bridge ground wireto the bridge plate
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

A fourth position plays both pickups in series, louder and thicker. Single coil in the neck, single coil in the bridge. 4-way blade. 1 volume, 1 tone (250k pots, 47 nF cap, modern tone wiring). The neck pickup is reverse wound, reverse polarity. Bridge ground to the bridge plate.

VolumeTurns the whole guitar up and down.
ToneRolls off treble on every pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the 4-way blade, Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Tone pot back to Volume pot back.
  2. Wire from 4-way blade B2 to Volume pot back.
  3. Wire from 4-way blade B3 to Volume pot back.
  4. Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
  5. Wire from Output jack sleeve to Volume pot back.
  6. Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from 4-way blade A1 to 4-way blade A2.
  2. Wire from 4-way blade A1 to 4-way blade B4.

Caps and resistors

  1. 47 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.

Switch and pot runs

  1. Wire from 4-way blade AC to Volume lug 3.
  2. Wire from Tone lug 2 to Volume lug 3.

To the output jack

  1. Wire from Output jack tip to Volume lug 2.

Pickups last

  1. Neck Tele pickup bare lead to Volume pot back.
  2. Neck Tele pickup white lead to 4-way blade AC.
  3. Neck Tele pickup black lead to 4-way blade BC.
  4. Bridge Tele pickup black lead to Tone pot back.
  5. Bridge Tele pickup white lead to 4-way blade A1.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
4-way blade 1 (bridge)bridgeabout 5.9k ohms
4-way blade 2 (both parallel)bridge parallel with neckabout 3.0k ohms
4-way blade 3 (neck)neckabout 5.9k ohms
4-way blade 4 (both series)bridge in series with neckabout 11.5k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this