Stock Tele style
Build code T2-FF-3B-V1T-A-47-M-001-NN
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: Tele pickup | RWRP: reverse wound, reverse polarity |
| 1 | Bridge pickup: Tele pickup | |
| 1 | 3-way blade | |
| 2 | 250k audio (A) pot | volume, tone |
| 1 | 47 nF (.047 µF, marked 473) capacitor | tone |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the bridge plate |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
Bridge, both, or neck on a 3-way blade. Single coil in the neck, single coil in the bridge. 3-way blade. 1 volume, 1 tone (250k pots, 47 nF cap, modern tone wiring). The neck pickup is reverse wound, reverse polarity. Bridge ground to the bridge plate.
| Volume | Turns the whole guitar up and down. |
| Tone | Rolls off treble on every pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 3-way blade, Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Tone pot back to Volume pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 3-way blade B2 to 3-way blade B3.
- Wire from 3-way blade A1 to 3-way blade A2.
- Wire from 3-way blade AC to 3-way blade BC.
Caps and resistors
- 47 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.
Switch and pot runs
- Wire from 3-way blade AC to Volume lug 3.
- Wire from Tone lug 2 to Volume lug 3.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck Tele pickup black and bare leads to Volume pot back.
- Neck Tele pickup white lead to 3-way blade B3.
- Bridge Tele pickup black lead to Tone pot back.
- Bridge Tele pickup white lead to 3-way blade A2.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 3-way blade 1 (bridge) | bridge | about 5.9k ohms |
| 3-way blade 2 (both) | bridge parallel with neck | about 3.0k ohms |
| 3-way blade 3 (neck) | neck | about 5.9k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.