Neck humbucker
Build code T2-HF-3B-V1T-A-47-M-001-NN
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: humbucker | |
| 1 | Bridge pickup: Tele pickup | |
| 1 | 3-way blade | |
| 2 | 500k audio (A) pot | volume, tone |
| 1 | 47 nF (.047 µF, marked 473) capacitor | tone |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the bridge plate |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
A humbucker in the neck and a single coil in the bridge. Humbucker in the neck, single coil in the bridge. 3-way blade. 1 volume, 1 tone (500k pots, 47 nF cap, modern tone wiring). Bridge ground to the bridge plate. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.
| Volume | Turns the whole guitar up and down. |
| Tone | Rolls off treble on every pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 3-way blade, Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Tone pot back to Volume pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 3-way blade B2 to 3-way blade B3.
- Wire from 3-way blade A1 to 3-way blade A2.
- Wire from 3-way blade AC to 3-way blade BC.
Caps and resistors
- 47 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.
Switch and pot runs
- Wire from 3-way blade AC to Volume lug 3.
- Wire from Tone lug 2 to Volume lug 3.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck humbucker: twist the red and white leads together, solder them and cover the joint with heat shrink or tape. This is the link between its two coils, and it touches nothing else.
- Neck humbucker green and bare leads to Volume pot back.
- Neck humbucker black lead to 3-way blade B3.
- Bridge Tele pickup black lead to Tone pot back.
- Bridge Tele pickup white lead to 3-way blade A2.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 3-way blade 1 (bridge) | bridge | about 5.9k ohms |
| 3-way blade 2 (both) | bridge parallel with neck | about 3.4k ohms |
| 3-way blade 3 (neck) | neck | about 7.9k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.