Wiring Bench

HH 5-way, inside and outside coils

Wiring diagram: Strat style, HH, 5-way Super Switch

Build code S3-HEH-SSE-V1T-A-22-M-001-NNN

Switching

Switching chart: 1 bridge, 2 one coil of each, 3 bridge + neck, 4 the other coil of each, 5 neck
Super Switch lugs in each position

Seen from the lug side. Orange shows the lugs each position joins.

Super Switch lugs in each position

Parts

QtyPart
1Neck pickup: humbucker
1Bridge pickup: humbucker
15-way Super Switch (4-pole)
2500k audio (A) potvolume, tone
122 nF (.022 µF, marked 223) capacitortone
1Mono output jack
1Bridge ground wireto the trem claw
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

Positions 2 and 4 each play one coil of each humbucker, and both pairs are quiet. Humbucker in the neck, humbucker in the bridge. 5-way Super Switch, inside and outside coils: bridge, one coil of each, bridge + neck, the other coil of each, neck. Which pair sits on the inside depends on how each humbucker is turned in its route. 1 volume, 1 tone (500k pots, 22 nF cap, modern tone wiring). Bridge ground to the trem claw. The middle route is left empty. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.

VolumeTurns the whole guitar up and down.
ToneRolls off treble on every pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the 5-way Super Switch (4-pole), Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Tone pot back to Volume pot back.
  2. Wire from 5-way Super Switch (4-pole) D2 to Volume pot back.
  3. Wire from 5-way Super Switch (4-pole) B4 to Tone pot back.
  4. Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
  5. Wire from Output jack sleeve to Volume pot back.
  6. Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from 5-way Super Switch (4-pole) A2 to 5-way Super Switch (4-pole) C4.
  2. Wire from 5-way Super Switch (4-pole) C1 to 5-way Super Switch (4-pole) C3.
  3. Wire from 5-way Super Switch (4-pole) C3 to 5-way Super Switch (4-pole) D1.
  4. Wire from 5-way Super Switch (4-pole) D1 to 5-way Super Switch (4-pole) D3.
  5. Wire from 5-way Super Switch (4-pole) A3 to 5-way Super Switch (4-pole) A5.
  6. Wire from 5-way Super Switch (4-pole) A3 to 5-way Super Switch (4-pole) B5.
  7. Wire from 5-way Super Switch (4-pole) B3 to 5-way Super Switch (4-pole) B5.

Caps and resistors

  1. 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.

Switch and pot runs

  1. Wire from 5-way Super Switch (4-pole) C4 to Volume lug 3.
  2. Wire from Tone lug 2 to Volume lug 3.

To the output jack

  1. Wire from Output jack tip to Volume lug 2.

Pickups last

  1. Neck humbucker green and bare leads to Volume pot back.
  2. Neck humbucker black lead to 5-way Super Switch (4-pole) C4.
  3. Neck humbucker red lead to 5-way Super Switch (4-pole) AC.
  4. Neck humbucker white lead to 5-way Super Switch (4-pole) BC.
  5. Bridge humbucker green and bare leads to Volume pot back.
  6. Bridge humbucker black lead to Volume lug 3.
  7. Bridge humbucker red lead to 5-way Super Switch (4-pole) CC.
  8. Bridge humbucker white lead to 5-way Super Switch (4-pole) DC.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
5-way Super Switch (4-pole) 1 (bridge)bridgeabout 7.9k ohms
5-way Super Switch (4-pole) 2 (one coil of each)bridge north coil parallel with neck south coilabout 2.0k ohms
5-way Super Switch (4-pole) 3 (bridge + neck)bridge parallel with neckabout 4.0k ohms
5-way Super Switch (4-pole) 4 (the other coil of each)bridge south coil parallel with neck north coilabout 2.0k ohms
5-way Super Switch (4-pole) 5 (neck)neckabout 7.9k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this