HSS Super Switch, lug by lug
Hand-wired example, so it has no build code.
Switching
Super Switch lugs in each position
Seen from the lug side. Orange shows the lugs each position joins.
Parts
| Qty | Part | |
|---|---|---|
| 1 | Bridge pickup: humbucker | |
| 1 | Middle pickup: single coil | RWRP: reverse wound, reverse polarity |
| 1 | Neck pickup: single coil | |
| 1 | 5-way Super Switch (4-pole) | |
| 2 | 500k audio (A) pot | volume, tone |
| 1 | 22 nF (.022 µF, marked 223) capacitor | tone |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
The 4-pole switch wired by hand, with one bridge coil and the middle in position 2.
| Volume | Turns the whole guitar up and down. |
| Tone | Rolls off treble on every pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 5-way Super Switch (4-pole), Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Tone pot back to Volume pot back.
- Wire from 5-way Super Switch (4-pole) B2 to Volume pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 5-way Super Switch (4-pole) A1 to 5-way Super Switch (4-pole) A2.
- Wire from 5-way Super Switch (4-pole) C2 to 5-way Super Switch (4-pole) C3.
- Wire from 5-way Super Switch (4-pole) C3 to 5-way Super Switch (4-pole) C4.
- Wire from 5-way Super Switch (4-pole) D4 to 5-way Super Switch (4-pole) D5.
- Wire from 5-way Super Switch (4-pole) AC to 5-way Super Switch (4-pole) CC.
- Wire from 5-way Super Switch (4-pole) CC to 5-way Super Switch (4-pole) DC.
Caps and resistors
- 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.
Switch and pot runs
- Wire from 5-way Super Switch (4-pole) DC to Volume lug 3.
- Wire from Tone lug 2 to Volume lug 3.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck single coil black lead to Volume pot back.
- Neck single coil white lead to 5-way Super Switch (4-pole) D5.
- Middle single coil black lead to Volume pot back.
- Middle single coil white lead to 5-way Super Switch (4-pole) C2.
- Bridge humbucker green and bare leads to Tone pot back.
- Bridge humbucker black lead to 5-way Super Switch (4-pole) A1.
- Bridge humbucker red and white leads to 5-way Super Switch (4-pole) BC.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 5-way Super Switch (4-pole) 1 (bridge HB) | bridge | about 15.5k ohms |
| 5-way Super Switch (4-pole) 2 (split + middle) | bridge north coil parallel with middle | about 3.4k ohms |
| 5-way Super Switch (4-pole) 3 (middle) | middle | about 5.9k ohms |
| 5-way Super Switch (4-pole) 4 (middle+neck) | middle parallel with neck | about 2.9k ohms |
| 5-way Super Switch (4-pole) 5 (neck) | neck | about 5.7k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
Stock HSS
A bridge humbucker and two single coils on a 5-way blade.
HSS, split on a mini toggle
A small on-on toggle splits the bridge humbucker in every position.
HSH on a 5-way Super Switch
Positions 2 and 4 pair one coil of a humbucker with the middle.
HSH Super Switch, high-pass pull
The HSH Super Switch wiring with a high-pass filter on the volume pull. Vai style.