Stock HSS
Build code S3-FFH-5W-V2B-A-22-M-001-NNN
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: single coil | |
| 1 | Middle pickup: single coil | RWRP: reverse wound, reverse polarity |
| 1 | Bridge pickup: humbucker | |
| 1 | 5-way blade | |
| 3 | 500k audio (A) pot | volume, tone neck mid, bridge tone |
| 1 | 22 nF (.022 µF, marked 223) capacitor | tone |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the trem claw |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
A bridge humbucker and two single coils on a 5-way blade. Single coil in the neck, single coil in the middle, humbucker in the bridge. 5-way blade. 1 volume, 2 tones (bridge tone, 500k pots, 22 nF cap, modern tone wiring). The middle pickup is reverse wound, reverse polarity. Bridge ground to the trem claw. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.
| Volume | Turns the whole guitar up and down. |
| Tone neck mid | Rolls off treble on the neck and middle pickups. Down makes it warmer and darker. |
| Bridge tone | Rolls off treble on the bridge pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 5-way blade, Volume, Tone neck mid, Bridge tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Tone neck mid pot back to Volume pot back.
- Bare wire from Bridge tone pot back to Tone neck mid pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 5-way blade AC to 5-way blade BC.
- Wire from 5-way blade B2 to 5-way blade B3.
Caps and resistors
- 22 nF cap: one leg on Tone neck mid lug 1, the other on Tone neck mid pot back. Caps have no right way round.
Switch and pot runs
- Wire from 5-way blade BC to Volume lug 3.
- Wire from 5-way blade B3 to Tone neck mid lug 2.
- Wire from 5-way blade B1 to Bridge tone lug 2.
- Wire from Bridge tone lug 1 to Tone neck mid lug 1.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck single coil black lead to Volume pot back.
- Neck single coil white lead to 5-way blade A3.
- Middle single coil black lead to Volume pot back.
- Middle single coil white lead to 5-way blade A2.
- Bridge humbucker: twist the red and white leads together, solder them and cover the joint with heat shrink or tape. This is the link between its two coils, and it touches nothing else.
- Bridge humbucker green and bare leads to Volume pot back.
- Bridge humbucker black lead to 5-way blade A1.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 5-way blade 1 (bridge) | bridge | about 7.9k ohms |
| 5-way blade 2 (bridge + middle) | bridge parallel with middle | about 3.4k ohms |
| 5-way blade 3 (middle) | middle | about 5.9k ohms |
| 5-way blade 4 (middle + neck) | middle parallel with neck | about 3.0k ohms |
| 5-way blade 5 (neck) | neck | about 5.9k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
HSS, split on a mini toggle
A small on-on toggle splits the bridge humbucker in every position.
HSS Super Switch, lug by lug
The 4-pole switch wired by hand, with one bridge coil and the middle in position 2.
HSH on a 5-way Super Switch
Positions 2 and 4 pair one coil of a humbucker with the middle.
HSH Super Switch, high-pass pull
The HSH Super Switch wiring with a high-pass filter on the volume pull. Vai style.