HH on a mini toggle
Build code S3-HEH-M3-V-A-22-M-001-NNN
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: humbucker | |
| 1 | Bridge pickup: humbucker | |
| 1 | 3-way mini toggle | |
| 1 | 500k audio (A) pot | volume |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the trem claw |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
A small on-on-on toggle picks neck, both, or bridge. One volume, no tone. Humbucker in the neck, humbucker in the bridge. Mini toggle (on-on-on). 1 volume only (500k pots). Bridge ground to the trem claw. The middle route is left empty. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.
| Volume | Turns the whole guitar up and down. |
Wiring instructions
Get the parts ready
- Mount the 3-way mini toggle, Volume and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 3-way mini toggle AC to 3-way mini toggle BC.
Switch and pot runs
- Wire from 3-way mini toggle BC to Volume lug 3.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck humbucker: twist the red and white leads together, solder them and cover the joint with heat shrink or tape. This is the link between its two coils, and it touches nothing else.
- Neck humbucker green and bare leads to Volume pot back.
- Neck humbucker black lead to 3-way mini toggle A up.
- Bridge humbucker: twist the red and white leads together, solder them and cover the joint with heat shrink or tape. This is the link between its two coils, and it touches nothing else.
- Bridge humbucker green and bare leads to Volume pot back.
- Bridge humbucker black lead to 3-way mini toggle B down.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 3-way mini toggle 1 (neck (up)) | neck | about 7.9k ohms |
| 3-way mini toggle 2 (both) | bridge parallel with neck | about 4.0k ohms |
| 3-way mini toggle 3 (bridge (down)) | bridge | about 7.9k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
Stock HSS
A bridge humbucker and two single coils on a 5-way blade.
HSS, split on a mini toggle
A small on-on toggle splits the bridge humbucker in every position.
HSS Super Switch, lug by lug
The 4-pole switch wired by hand, with one bridge coil and the middle in position 2.
HSH on a 5-way Super Switch
Positions 2 and 4 pair one coil of a humbucker with the middle.