HH toggle, split and high-pass
Build code S3-HEH-3T-V1T-A-22-M-001-SNS-JH-U
Not confirmed yet: 330 pF high-pass cap. The most often reported value for this pull, not confirmed from the maker.
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: humbucker | |
| 1 | Bridge pickup: humbucker | |
| 1 | 3-way toggle | |
| 2 | 500k audio (A) push-pull pot (DPDT) | volume, tone |
| 1 | 22 nF (.022 µF, marked 223) capacitor | tone |
| 1 | 330 pF (marked 331) capacitor | treble bleed / high-pass |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the trem claw |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
The tone knob splits both humbuckers and the volume pulls up a high-pass filter. Satriani style. Humbucker in the neck, humbucker in the bridge. 3-way toggle. 1 volume, 1 tone (500k pots, 22 nF cap, modern tone wiring). Pull the tone knob to split both the neck and bridge humbuckers. Pull the volume knob: high-pass on. The high-pass filter is a 330 pF cap, the value most often reported for this pull. Check it against your guitar's own diagram. Bridge ground to the trem claw. The middle route is left empty. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.
| Volume | Turns the whole guitar up and down. |
| Tone | Rolls off treble on every pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 3-way toggle, Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Tone pot back to Volume pot back.
- Short wire from Tone A up to Tone pot back, or bend the lug down onto the pot back.
- Short wire from Tone B up to Tone pot back, or bend the lug down onto the pot back.
- Wire from 3-way toggle frame to Tone pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 3-way toggle neck out to 3-way toggle bridge out.
- Wire from Volume lug 2 to Volume A up.
Caps and resistors
- 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.
- 330 pF cap: one leg on Volume lug 3, the other on Volume AC. Caps have no right way round.
Switch and pot runs
- Wire from 3-way toggle neck out to Volume lug 3.
- Wire from Tone lug 2 to Volume lug 3.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck humbucker green and bare leads to Volume pot back.
- Neck humbucker black lead to 3-way toggle neck in.
- Neck humbucker red and white leads to Tone AC.
- Bridge humbucker green and bare leads to Volume pot back.
- Bridge humbucker black lead to 3-way toggle bridge in.
- Bridge humbucker red and white leads to Tone BC.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 3-way toggle 1 (neck (up)), Volume down (pushed: high-pass off), Tone down (pushed: neck and bridge humbuckers) | neck | about 7.9k ohms |
| 3-way toggle 1 (neck (up)), Volume down (pushed: high-pass off), Tone up (pulled: neck and bridge split) | neck north coil | about 4.0k ohms |
| 3-way toggle 1 (neck (up)), Volume up (pulled: high-pass on), Tone down (pushed: neck and bridge humbuckers) | neck | about 7.9k ohms |
| 3-way toggle 1 (neck (up)), Volume up (pulled: high-pass on), Tone up (pulled: neck and bridge split) | neck north coil | about 4.0k ohms |
| 3-way toggle 2 (both), Volume down (pushed: high-pass off), Tone down (pushed: neck and bridge humbuckers) | bridge parallel with neck | about 4.0k ohms |
| 3-way toggle 2 (both), Volume down (pushed: high-pass off), Tone up (pulled: neck and bridge split) | bridge north coil parallel with neck north coil | about 2.0k ohms |
| 3-way toggle 2 (both), Volume up (pulled: high-pass on), Tone down (pushed: neck and bridge humbuckers) | bridge parallel with neck | about 4.0k ohms |
| 3-way toggle 2 (both), Volume up (pulled: high-pass on), Tone up (pulled: neck and bridge split) | bridge north coil parallel with neck north coil | about 2.0k ohms |
| 3-way toggle 3 (bridge (down)), Volume down (pushed: high-pass off), Tone down (pushed: neck and bridge humbuckers) | bridge | about 7.9k ohms |
| 3-way toggle 3 (bridge (down)), Volume down (pushed: high-pass off), Tone up (pulled: neck and bridge split) | bridge north coil | about 4.0k ohms |
| 3-way toggle 3 (bridge (down)), Volume up (pulled: high-pass on), Tone down (pushed: neck and bridge humbuckers) | bridge | about 7.9k ohms |
| 3-way toggle 3 (bridge (down)), Volume up (pulled: high-pass on), Tone up (pulled: neck and bridge split) | bridge north coil | about 4.0k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
Stock HSS
A bridge humbucker and two single coils on a 5-way blade.
HSS, split on a mini toggle
A small on-on toggle splits the bridge humbucker in every position.
HSS Super Switch, lug by lug
The 4-pole switch wired by hand, with one bridge coil and the middle in position 2.
HSH on a 5-way Super Switch
Positions 2 and 4 pair one coil of a humbucker with the middle.