Wiring Bench

HSH Super Switch, high-pass pull

Wiring diagram: Strat style, HSH, 5-way Super Switch

Build code S3-HFH-SSA-V1T-A-22-M-001-NNN-JH

Not confirmed yet: 330 pF high-pass cap. The most often reported value for this pull, not confirmed from the maker.

Switching

Switching chart: 1 bridge, 2 bridge coil + middle, 3 middle, 4 middle + neck coil, 5 neck
Super Switch lugs in each position

Seen from the lug side. Orange shows the lugs each position joins.

Super Switch lugs in each position

Parts

QtyPart
1Neck pickup: humbucker
1Middle pickup: single coilRWRP: reverse wound, reverse polarity
1Bridge pickup: humbucker
15-way Super Switch (4-pole)
1500k audio (A) push-pull pot (DPDT)volume
1500k audio (A) pottone
122 nF (.022 µF, marked 223) capacitortone
1330 pF (marked 331) capacitortreble bleed / high-pass
1Mono output jack
1Bridge ground wireto the trem claw
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

The HSH Super Switch wiring with a high-pass filter on the volume pull. Vai style. Humbucker in the neck, single coil in the middle, humbucker in the bridge. 5-way Super Switch, splits in 2 and 4: bridge, bridge coil + middle, middle, middle + neck coil, neck. 1 volume, 1 tone (500k pots, 22 nF cap, modern tone wiring). The middle pickup is reverse wound, reverse polarity. Pull the volume knob: high-pass on. The high-pass filter is a 330 pF cap, the value most often reported for this pull. Check it against your guitar's own diagram. Bridge ground to the trem claw. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.

VolumeTurns the whole guitar up and down.
ToneRolls off treble on every pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the 5-way Super Switch (4-pole), Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Tone pot back to Volume pot back.
  2. Wire from 5-way Super Switch (4-pole) C2 to Tone pot back.
  3. Wire from 5-way Super Switch (4-pole) D4 to Volume pot back.
  4. Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
  5. Wire from Output jack sleeve to Volume pot back.
  6. Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from 5-way Super Switch (4-pole) A5 to 5-way Super Switch (4-pole) B4.
  2. Wire from 5-way Super Switch (4-pole) A3 to 5-way Super Switch (4-pole) B2.
  3. Wire from 5-way Super Switch (4-pole) A3 to 5-way Super Switch (4-pole) A4.
  4. Wire from 5-way Super Switch (4-pole) A1 to 5-way Super Switch (4-pole) A2.
  5. Wire from 5-way Super Switch (4-pole) AC to 5-way Super Switch (4-pole) BC.
  6. Wire from Volume lug 2 to Volume A up.

Caps and resistors

  1. 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.
  2. 330 pF cap: one leg on Volume lug 3, the other on Volume AC. Caps have no right way round.

Switch and pot runs

  1. Wire from 5-way Super Switch (4-pole) AC to Volume lug 3.
  2. Wire from Tone lug 2 to Volume lug 3.

To the output jack

  1. Wire from Output jack tip to Volume lug 2.

Pickups last

  1. Neck humbucker green and bare leads to Volume pot back.
  2. Neck humbucker black lead to 5-way Super Switch (4-pole) B4.
  3. Neck humbucker red and white leads to 5-way Super Switch (4-pole) DC.
  4. Middle single coil black lead to Volume pot back.
  5. Middle single coil white lead to 5-way Super Switch (4-pole) A3.
  6. Bridge humbucker green and bare leads to Volume pot back.
  7. Bridge humbucker black lead to 5-way Super Switch (4-pole) A1.
  8. Bridge humbucker red and white leads to 5-way Super Switch (4-pole) CC.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
5-way Super Switch (4-pole) 1 (bridge), Volume down (pushed: high-pass off)bridgeabout 7.9k ohms
5-way Super Switch (4-pole) 1 (bridge), Volume up (pulled: high-pass on)bridgeabout 7.9k ohms
5-way Super Switch (4-pole) 2 (bridge coil + middle), Volume down (pushed: high-pass off)bridge north coil parallel with middleabout 2.4k ohms
5-way Super Switch (4-pole) 2 (bridge coil + middle), Volume up (pulled: high-pass on)bridge north coil parallel with middleabout 2.4k ohms
5-way Super Switch (4-pole) 3 (middle), Volume down (pushed: high-pass off)middleabout 5.9k ohms
5-way Super Switch (4-pole) 3 (middle), Volume up (pulled: high-pass on)middleabout 5.9k ohms
5-way Super Switch (4-pole) 4 (middle + neck coil), Volume down (pushed: high-pass off)middle parallel with neck north coilabout 2.4k ohms
5-way Super Switch (4-pole) 4 (middle + neck coil), Volume up (pulled: high-pass on)middle parallel with neck north coilabout 2.4k ohms
5-way Super Switch (4-pole) 5 (neck), Volume down (pushed: high-pass off)neckabout 7.9k ohms
5-way Super Switch (4-pole) 5 (neck), Volume up (pulled: high-pass on)neckabout 7.9k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this