HSH Super Switch, stacked middle
Build code S3-HRH-SSF-V1T-A-22-M-001-NNN
Not confirmed yet: Positions 2 and 4 on the stacked-middle HSH. Which coils play is our best reading of the switch, not yet checked against the maker's diagram.
Switching
Super Switch lugs in each position
Seen from the lug side. Orange shows the lugs each position joins.
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: humbucker | |
| 1 | Middle pickup: single-size humbucker | |
| 1 | Bridge pickup: humbucker | |
| 1 | 5-way Super Switch (4-pole) | |
| 2 | 500k audio (A) pot | volume, tone |
| 1 | 22 nF (.022 µF, marked 223) capacitor | tone |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | to the trem claw |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
For a stacked or rail middle: positions 2 and 4 pair one coil of the middle with an outer coil. Humbucker in the neck, single-size humbucker in the middle, humbucker in the bridge. 5-way Super Switch, splits in 2 and 4, middle too: bridge, bridge coil + middle coil, middle, middle coil + neck coil, neck. 1 volume, 1 tone (500k pots, 22 nF cap, modern tone wiring). Bridge ground to the trem claw. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.
| Volume | Turns the whole guitar up and down. |
| Tone | Rolls off treble on every pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 5-way Super Switch (4-pole), Volume, Tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Tone pot back to Volume pot back.
- Wire from 5-way Super Switch (4-pole) BC to Volume pot back.
- Short wire from Volume lug 1 to Volume pot back, or bend the lug down onto the pot back.
- Wire from Output jack sleeve to Volume pot back.
- Wire from Bridge ground wire to Volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 5-way Super Switch (4-pole) AC to 5-way Super Switch (4-pole) CC.
- Wire from 5-way Super Switch (4-pole) B2 to 5-way Super Switch (4-pole) B4.
Caps and resistors
- 22 nF cap: one leg on Tone lug 1, the other on Tone pot back. Caps have no right way round.
Switch and pot runs
- Wire from 5-way Super Switch (4-pole) CC to Volume lug 3.
- Wire from Tone lug 2 to Volume lug 3.
To the output jack
- Wire from Output jack tip to Volume lug 2.
Pickups last
- Neck humbucker green and bare leads to Volume pot back.
- Neck humbucker black lead to 5-way Super Switch (4-pole) A5.
- Neck humbucker red and white leads to 5-way Super Switch (4-pole) A4.
- Middle single-size humbucker bare lead to Volume pot back.
- Middle single-size humbucker black lead to Volume lug 3.
- Middle single-size humbucker red and white leads to 5-way Super Switch (4-pole) B2.
- Middle single-size humbucker green lead to 5-way Super Switch (4-pole) B3.
- Bridge humbucker green and bare leads to Volume pot back.
- Bridge humbucker black lead to 5-way Super Switch (4-pole) C1.
- Bridge humbucker red and white leads to 5-way Super Switch (4-pole) C2.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 5-way Super Switch (4-pole) 1 (bridge) | bridge | about 7.9k ohms |
| 5-way Super Switch (4-pole) 2 (bridge coil + middle coil) | bridge south coil parallel with middle north coil | about 2.0k ohms |
| 5-way Super Switch (4-pole) 3 (middle) | middle | about 7.9k ohms |
| 5-way Super Switch (4-pole) 4 (middle coil + neck coil) | middle north coil parallel with neck south coil | about 2.0k ohms |
| 5-way Super Switch (4-pole) 5 (neck) | neck | about 7.9k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
Stock HSS
A bridge humbucker and two single coils on a 5-way blade.
HSS, split on a mini toggle
A small on-on toggle splits the bridge humbucker in every position.
HSS Super Switch, lug by lug
The 4-pole switch wired by hand, with one bridge coil and the middle in position 2.
HSH on a 5-way Super Switch
Positions 2 and 4 pair one coil of a humbucker with the middle.