Shielded Les Paul style
Hand-wired example, so it has no build code.
Switching
Parts
| Qty | Part | |
|---|---|---|
| 1 | Neck pickup: humbucker | |
| 1 | Bridge pickup: humbucker | |
| 1 | 3-way toggle | |
| 4 | 500k audio (A) pot | neck volume, bridge volume, neck tone, bridge tone |
| 2 | 22 nF (.022 µF, marked 223) capacitor | one per tone knob |
| 1 | Mono output jack | |
| 1 | Bridge ground wire | |
| 1 | Hookup wire, 22 AWG | two or three colors, plus bare or black for grounds |
| 1 | Solder and heat shrink or tape | for joined pickup leads |
About this wiring
50s wiring with copper foil in the control cavity against hum and buzz.
| Neck volume | Turns the neck pickup up and down. With more than one pickup on, all the way down cuts the whole guitar. |
| Bridge volume | Turns the bridge pickup up and down. With more than one pickup on, all the way down cuts the whole guitar. |
| Neck tone | Rolls off treble on the neck pickup. Down makes it warmer and darker. |
| Bridge tone | Rolls off treble on the bridge pickup. Down makes it warmer and darker. |
Wiring instructions
Get the parts ready
- Mount the 3-way toggle, Neck volume, Bridge volume, Neck tone, Bridge tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
- Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.
Grounds first
- Bare wire from Bridge volume pot back to Neck volume pot back.
- Bare wire from Neck tone pot back to Neck volume pot back.
- Bare wire from Bridge tone pot back to Neck tone pot back.
- Short wire from Neck volume lug 1 to Neck volume pot back, or bend the lug down onto the pot back.
- Short wire from Bridge volume lug 1 to Bridge volume pot back, or bend the lug down onto the pot back.
- Wire from 3-way toggle frame to Neck volume pot back.
- Short wire from Neck tone lug 1 to Neck tone pot back, or bend the lug down onto the pot back.
- Short wire from Bridge tone lug 1 to Bridge tone pot back, or bend the lug down onto the pot back.
- Wire from Foil g to Bridge volume pot back.
- Wire from Output jack sleeve to Bridge volume pot back.
- Wire from Bridge ground wire to Bridge volume pot back. It runs through the body to the bridge, so leave it long.
Jumpers on one part
- Wire from 3-way toggle neck out to 3-way toggle bridge out.
Caps and resistors
- 22 nF cap: one leg on Neck volume lug 2, the other on Neck tone lug 2. Caps have no right way round.
- 22 nF cap: one leg on Bridge volume lug 2, the other on Bridge tone lug 2. Caps have no right way round.
Switch and pot runs
- Wire from 3-way toggle neck in to Neck volume lug 2.
- Wire from 3-way toggle bridge in to Bridge volume lug 2.
To the output jack
- Wire from Output jack tip to 3-way toggle bridge out.
Pickups last
- Neck humbucker: twist the green and white leads together, solder them and cover the joint with heat shrink or tape. This is the link between its two coils, and it touches nothing else.
- Neck humbucker black and bare leads to Neck volume pot back.
- Neck humbucker red lead to Neck volume lug 3.
- Bridge humbucker: twist the green and white leads together, solder them and cover the joint with heat shrink or tape. This is the link between its two coils, and it touches nothing else.
- Bridge humbucker black and bare leads to Bridge volume pot back.
- Bridge humbucker red lead to Bridge volume lug 3.
Check it with a meter
- Set the meter to ohms, on the 20k range (or auto).
- Guitar unplugged. Turn every volume and tone knob up to 10.
- Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
- Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
- Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
| Position | Plays | Expect |
|---|---|---|
| 3-way toggle 1 (neck (up)) | neck | about 7.5k ohms |
| 3-way toggle 2 (both) | bridge parallel with neck | about 3.9k ohms |
| 3-way toggle 3 (bridge (down)) | bridge | about 8.3k ohms |
Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.
If a reading is off
- 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
- No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
- A two-pickup position reads like one pickup: one of them isn't connected on the switch.
- Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.
More like this
Stock Les Paul style
A volume and a tone for each pickup on a 3-way toggle. Pick 50s or modern tone wiring later.
Split both humbuckers
Pull either tone knob for a single coil sound from that pickup.
Series or parallel
Pull either tone knob to put that humbucker's coils in parallel: brighter, still quiet.
Jimmy Page style
Four push-pulls split each pickup, flip the neck's phase, or put both in series.