Wiring Bench

Split both humbuckers

Wiring diagram: Les Paul style, HH, 3-way toggle

Build code L2-HH-3T-2V2T-A-22-M-000-SS

Switching

Switching chart: 1 neck (up), 2 both, 3 bridge (down)

Parts

QtyPart
1Neck pickup: humbucker
1Bridge pickup: humbucker
13-way toggle
2500k audio (A) potneck volume, bridge volume
2500k audio (A) push-pull pot (DPDT)neck tone, bridge tone
222 nF (.022 µF, marked 223) capacitorone per tone knob
1Mono output jack
1Bridge ground wireto the tailpiece stud
1Hookup wire, 22 AWGtwo or three colors, plus bare or black for grounds
1Solder and heat shrink or tapefor joined pickup leads

About this wiring

Pull either tone knob for a single coil sound from that pickup. Humbucker in the neck, humbucker in the bridge. 3-way toggle. 2 volumes, 2 tones (500k pots, 22 nF cap, modern tone wiring). Pull the neck tone knob to split the neck humbucker. Pull the bridge tone knob to split the bridge humbucker. Bridge ground to the tailpiece stud. Humbucker leads are drawn in Seymour Duncan colors (black hot). Makers differ, so check yours on the Tools page.

Neck volumeTurns the neck pickup up and down. With more than one pickup on, all the way down cuts the whole guitar.
Neck toneRolls off treble on the neck pickup. Down makes it warmer and darker.
Bridge volumeTurns the bridge pickup up and down. With more than one pickup on, all the way down cuts the whole guitar.
Bridge toneRolls off treble on the bridge pickup. Down makes it warmer and darker.

Wiring instructions

Get the parts ready

  1. Mount the 3-way toggle, Neck volume, Neck tone, Bridge volume, Bridge tone and Output jack where the drawing shows them. Face the pot lugs the way they're drawn.
  2. Tin every lug and every wire end with a little solder first. Scuff a spot on each pot back with sandpaper so ground wires take solder.

Grounds first

  1. Bare wire from Bridge volume pot back to Neck volume pot back.
  2. Bare wire from Neck tone pot back to Neck volume pot back.
  3. Bare wire from Bridge tone pot back to Neck tone pot back.
  4. Short wire from Neck tone A up to Neck tone pot back, or bend the lug down onto the pot back.
  5. Short wire from Bridge tone A up to Bridge tone pot back, or bend the lug down onto the pot back.
  6. Wire from 3-way toggle frame to Neck volume pot back.
  7. Short wire from Neck volume lug 1 to Neck volume pot back, or bend the lug down onto the pot back.
  8. Short wire from Bridge volume lug 1 to Bridge volume pot back, or bend the lug down onto the pot back.
  9. Wire from Output jack sleeve to Bridge volume pot back.
  10. Wire from Bridge ground wire to Bridge volume pot back. It runs through the body to the bridge, so leave it long.

Jumpers on one part

  1. Wire from 3-way toggle neck out to 3-way toggle bridge out.

Caps and resistors

  1. 22 nF cap: one leg on Neck tone lug 1, the other on Neck tone pot back. Caps have no right way round.
  2. 22 nF cap: one leg on Bridge tone lug 1, the other on Bridge tone pot back. Caps have no right way round.

Switch and pot runs

  1. Wire from Neck tone lug 2 to Neck volume lug 3.
  2. Wire from Bridge tone lug 2 to Bridge volume lug 3.
  3. Wire from 3-way toggle neck in to Neck volume lug 2.
  4. Wire from 3-way toggle bridge in to Bridge volume lug 2.

To the output jack

  1. Wire from Output jack tip to 3-way toggle bridge out.

Pickups last

  1. Neck humbucker green and bare leads to Neck volume pot back.
  2. Neck humbucker black lead to Neck volume lug 3.
  3. Neck humbucker red and white leads to Neck tone AC.
  4. Bridge humbucker green and bare leads to Bridge volume pot back.
  5. Bridge humbucker black lead to Bridge volume lug 3.
  6. Bridge humbucker red and white leads to Bridge tone AC.
Check it with a meter
  1. Set the meter to ohms, on the 20k range (or auto).
  2. Guitar unplugged. Turn every volume and tone knob up to 10.
  3. Touch one probe to the jack tip and the other to the sleeve, or plug a cable in and touch its tip and sleeve.
  4. Click through each switch position and compare with the table. Within about 15 percent is fine: every pickup reads a little different.
  5. Turn the volume to 0: the reading should drop to almost nothing. If it doesn't, check the volume lugs.
PositionPlaysExpect
3-way toggle 1 (neck (up)), Neck tone down (pushed: neck humbucker), Bridge tone down (pushed: bridge humbucker)neckabout 7.9k ohms
3-way toggle 1 (neck (up)), Neck tone down (pushed: neck humbucker), Bridge tone up (pulled: bridge split)neckabout 7.9k ohms
3-way toggle 1 (neck (up)), Neck tone up (pulled: neck split), Bridge tone down (pushed: bridge humbucker)neck north coilabout 4.0k ohms
3-way toggle 1 (neck (up)), Neck tone up (pulled: neck split), Bridge tone up (pulled: bridge split)neck north coilabout 4.0k ohms
3-way toggle 2 (both), Neck tone down (pushed: neck humbucker), Bridge tone down (pushed: bridge humbucker)bridge parallel with neckabout 3.9k ohms
3-way toggle 2 (both), Neck tone down (pushed: neck humbucker), Bridge tone up (pulled: bridge split)bridge north coil parallel with neckabout 2.6k ohms
3-way toggle 2 (both), Neck tone up (pulled: neck split), Bridge tone down (pushed: bridge humbucker)bridge parallel with neck north coilabout 2.6k ohms
3-way toggle 2 (both), Neck tone up (pulled: neck split), Bridge tone up (pulled: bridge split)bridge north coil parallel with neck north coilabout 2.0k ohms
3-way toggle 3 (bridge (down)), Neck tone down (pushed: neck humbucker), Bridge tone down (pushed: bridge humbucker)bridgeabout 7.9k ohms
3-way toggle 3 (bridge (down)), Neck tone down (pushed: neck humbucker), Bridge tone up (pulled: bridge split)bridge north coilabout 4.0k ohms
3-way toggle 3 (bridge (down)), Neck tone up (pulled: neck split), Bridge tone down (pushed: bridge humbucker)bridgeabout 7.9k ohms
3-way toggle 3 (bridge (down)), Neck tone up (pulled: neck split), Bridge tone up (pulled: bridge split)bridge north coilabout 4.0k ohms

Readings assume typical pickups. Yours can be off by 15 percent or so and still be fine.

If a reading is off

  • 0 in every position: the hot run touches ground somewhere. Look for a stray strand or a solder blob.
  • No reading in a position that should play: a joint is open. Reflow the joints on that pickup's run.
  • A two-pickup position reads like one pickup: one of them isn't connected on the switch.
  • Readings are right but a two-pickup sound is thin and quiet: the pickups are out of phase. Swap one pickup's hot and ground leads.

More like this

Split both humbuckers wiring diagram | Wiring Bench